The 12V Solar Pumping Kit for continuous use incorporates a Shurflo pump that works with a 12V power supply.

Characteristics of the 12V Solar Pumping Kit system for continuous use

The photovoltaic system provided in the attached file can generate 0.48 kWh per day in winter (3 hours of sunshine) and 1.12 kWh in summer (7 hours of sunshine).

The characteristics of the proposed system are the following:

• Installed solar generation: 160 W
• Daily production in winter: 0.48 kWh
• Summer: daily production: 1.12 kWh
• Annual average daily production: 0.80 kWh

Components of the Solar Pumping Kit 12V continuous use

1 x ERA Polycrystalline 160W 12V Solar Panel: a 25-year warranty provides high reliability for our photovoltaic systems. It can supply the solar system with about 500 Wh per day in winter and almost twice as much in summer. Includes 1 meter of cable for each pole (both positive and negative). Including the connection box at the rear of the solar module. This photovoltaic module comes with a pre-assembled frame made of anodized aluminum.

1 x ATERSA PM5 12V Water Pump Controller: Atersa's PM5 water pump controller allows you to install a 12V water pump without a battery. Ideal for direct pumping systems and pressure groups where the water needs to be pumped or moved horizontally.

2 x Level Probe for ATERSA PM5 Controller: ATERSA's PM5 Level Probe is available in 12V and 24V and is used to control water pumps that use directly through solar panels.

1 x Shurflo Pressure Pump 12V 2088-443-144 10 l/min: it can produce at 0 m depth, but at height 28 it has a flow rate of 7.9 l/min m. Introducing the Shurflo 2088 514 145 booster set. The pump runs on 12V DC and can pump 13.6 liters per minute at a maximum pressure of 2.8 bar. You want to open a pressure tap or heater, either gas or electric. This pressure group can be used for continuous use. This means that the integrated motor cannot heat up to dangerous temperatures for the pressure pump, so it can run 24 hours a day. Thanks to this engine, you can keep the pressure groups continuously connected and use them as continuous consumption pressure groups. Consult the product or the technical data sheet.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m red: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m black: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x WEIDMULLER PVStick Connectors – Most recommended if you don't have crimping tools that can connect normal MC4 connectors. They are compatible with all connector models that come standard with solar panels and require no tools to connect to the cable.

The Solar Panel Kit 600W 12V 1000Whdia, feeds small consumers such as televisions, lamps, laptops, etc.

Characteristics of the Solar Panel Kit 600W 12V 1000Whdia system

The photovoltaic system provided in the attached file can generate 0.60 kWh per day in winter (3 hours of sunshine) and 1.40 kWh in summer (7 hours of sunshine).

The characteristics of the proposed system are the following:

• Installed solar generation: 200 W
• Maximum output power to housing: 600W
• Daily production in winter: 0.60 kWh
• Summer: daily production: 1.40 kWh
• Annual average daily production: 1.00 kWh

Components of the Solar Panel Kit 600W 12V 1000Whdia

1 x Solar Panel MUST 200W 12V Monocrystalline; suitable for caravans and 12V installations. It consists of 32 monocrystalline cells, weighs 10.3 kg and has dimensions of 1290 × 760 × 30 mm. The efficiency of the module is 20.4%, making it a very good option for small isolated houses with 3 or 4 panels and a 12V battery installed.

1 x Ultracell UCG-172-12 12V 172Ah GEL Battery: From leading brands like Ultracell, this GEL battery guarantees maximum performance and longevity for your solar kit. This is a deep cycle and represents the best in lead-acid battery technology with a GEL electrolyte. The life expectancy is over 1200 cycles, but if discharged below 30%, the battery life can be easily doubled and shortened. The GEL electrolyte is maintenance free and does not out gas, making it a very safe battery for indoor use. The battery has F11 screw terminals and weighs approximately 43 kg.

1 x 12V / 24V 20A PWM Must Solar Regulator: the 20A charge regulator works with a 12Vdc or 24Vdc battery and reports all the battery charging information (general operating status, battery voltage, current produced and temperature) from the panel includes an LCD screen to display In addition, this 10A solar charge controller from the manufacturer Must Solar can be easily configured to accurately charge batteries regardless of technology, ensuring perfect results and long battery life. It features a 12Vdc or 24Vdc output for DC-powered charging, 2 USB ports for charging mobile devices, and offers a 2-year manufacturer's warranty. The charge controller has protection against PV array short circuit, PV reverse connection, battery reverse connection, overload and output short circuit. Available from 10A to 60A in 12V DC and 24V DC models.

1 x 600W 12V Must Solar Inverter Charger: integrates a battery charger in one device, providing a very useful solution for small solar power systems. The nominal power is 600W and the maximum power for 20ms is 1800W. The nominal output voltage is 230 VAC. The battery supply voltage is 12 VDC. You can check the load, battery voltage, current, etc. on the LCD screen. This battery charger allows you to charge your battery from an external generator or power supply and features 10A at 12V. Compatible with sealed and open lead acid batteries. 0.5 meter cable of the required section is included. Inverter warranty is 2 years.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m red: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m black: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

2 x 6mm Cable Eye Terminal - 8mm Eye: used to crimp 6mm gauge cables and connect with 8mm diameter screws.

1 x WEIDMULLER PVStick Connectors – Most recommended if you don't have crimping tools that can connect normal MC4 connectors. They are compatible with all connector models that come standard with solar panels and require no tools to connect to the cable.

The 400W balcony solar panel kit is lightweight and easy to install, making it an alternative to rooftop panels.

The 400W solar kit for balconies is the latest innovation so that people who do not have a roof or a place to install solar panels can benefit from the economic savings on their electricity bills that the installation of a solar energy system entails. self-consumption.

The 400W solar kit for balconies includes 2 flexible 1 x 1 meter solar panels plus a state-of-the-art 300W microinverter, this solar panel is more resistant, lighter than traditional panels, which makes it easier to install and manage. It is made with the latest generation PERC solar cells with a high efficiency of 23.5%.

The uniquely designed PERC 9BB cell technology offers very high performance in a small footprint. It is also more durable than other mono solar cells. It reduces the risk of cell breakage and damage to the busbars, increases the stability and reliability of solar panels and increases production, in addition its uniform color allows it to better integrate with the environment and improve the aesthetics of the installation.

The PERC system is a significant improvement over traditional standard solar cells as it increases energy density and ROI. It features advanced diffusion technique to ensure uniformity in solar panel energy conversion. Its components are up to 23.5% efficient, producing more energy per unit area. Conventional standard solar cells are only 18-19%.

Characteristics of the 400W solar kit for balconies

• Durability: state-of-the-art technology.
• Solar Cell: Made of Grade A PERC 9BB monocrystalline solar cells.
• Premium EFTE Film – This film features superior light transmission and weather resistant performance.
• Shade tolerant.
• Tabletop: Durable fiberglass tabletop with better heat dissipation and heat resistant PET/TPT tabletop.
• Ultra-thin: only 3mm thick.
• Installation: can be fixed with adhesive, grommets, zip ties or Velcro.
• Net Weight: 9 lbs/4 kg.
• Back sheet: black fiberglass
• J-Box: IP 68 rated with 90cm/3ft cables.

​Technical description of the 400W solar kit for balconies

• Electrical information:
• Model: LS-200FX2-9BB
• Panel maximum power: 200W
• Number of kit panels: 2 units
• Microinverter: 300W
• Solar cell efficiency: 23.5%
• Maximum supply voltage: 18V
• Maximum power current: 11.1A
• Open Circuit Voltage: 21.24V
• Short circuit current: 12.2A
• Power Allocation Range: +/-3%
• Maximum system voltage: 500V
• Values under standard test conditions: Air mass - AM1.5, Irradiance - 1000W/m2, Cell temperature - 25°C.

The 24V Solar Pumping Kit for intermittent use incorporates a Shurflo pump that works with a 24V power supply.

Characteristics of the 24V Solar Pumping Kit system for intermittent use

The photovoltaic system proposed in the annex can generate 0.84 kWh per day (3 hours of sun) in winter and 1.96 kWh per day (7 hours of sun) in summer.

The recommended system characteristics are as follows.

• Installed solar power: 280W
• Daily production in winter: 0.84 kWh
• Daily production Summer: 1.96 kWh
• Annual average daily production: 1.40 kWh

Components of the Solar Pumping Kit 24V intermittent use

1 x 280W Polycrystalline Solar Panel: it is a model called "grid connection" where the voltage is neither 12V nor 24V. With a 25-year performance guarantee made from polycrystalline silicon, our solar systems offer superior performance and high operational reliability. Due to the supply of non-standard voltages, the recommended connection series must be respected and used with MPPT controllers or grid connection systems. With 60 cells, this solar panel is one of the most powerful you can buy today and can deliver an average of around, 1400Wh per day to the solar system. Keep in mind that production is much higher in summer than in winter. winter. Includes 1 meter cable for each pole with MC4 connectors at each end. A junction box with IP67 protection is included on the back of the solar panel. This photovoltaic panel comes with a pre-assembled aluminum frame and is ready to be fixed to any structure.

2 x Level Probe for ATERSA PM5 Controller: ATERSA's PM5 Level Probe is available in 12V and 24V and is used to control water pumps that use directly through solar panels.

1 x ATERSA PM5 24V Water Pump Controller: Atersa's PM5 water pump controller allows you to install a 24V water pump without a battery. Ideal for direct pumping systems and pressure groups where the water needs to be pumped or moved horizontally.

1 x Shurflo Pressure Pump 24V 2088-474-144 11 l/min: it is the perfect solution for pumping water from less than 3.6 meters or moving water from rivers and reservoirs to reservoirs and ponds. This system allows the device to be battery-free, so the water is only used during the day. Shurflo pressure pumps are excellent for pumping and moving water. Thanks to the ATERSA controller and the 190W 24V solar panel, the system works without batteries. Consult the product or the technical data sheet.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m red: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m black: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x WEIDMULLER PVStick Connectors - Most recommended if you don't have crimping tools that can connect normal MC4 connectors. They are compatible with all connector models that come standard with solar panels and require no tools to connect to the cable.

The Solar Kit for Caravans 600W 12V 1000Whdia, great fall arrest system for caravans with additional roof space.

Characteristics of the Solar Kit for Caravans 600W 12V 1000Whdia system

The photovoltaic system provided in the attached file can generate 1.22 kWh per day in winter (3 hours of sunshine) and 2.84 kWh in summer (7 hours of sunshine).

The characteristics of the proposed system are the following:

• Installed solar generation: 405 W
• Maximum output power to housing: 600VA
• Daily production in winter: 1.22 kWh
• Summer: daily production: 2.84 kWh
• Annual average daily production: 2.03 kWh

Components of the Solar Kit for Caravans 600W 12V 1000Whdia

1x 405W Deep Blue 3.0 JA Solar Mono Solar Panel:  have very special properties. It contains a half cell that provides a very high level of efficiency with a power of 405W. Powered by PERC technology and supplied by world-renowned manufacturer JA Solar.

1 x ABS Solar panel support for caravans: includes cable glands to insert solar module cables and Sika brand adhesive from the outside. The ABS support consists of 4 corners and 2 supports in the long part that delimit the structure of the solar panel. This structure can be fixed with a special ABS glue. The ABS construction is helpful in preventing the solar panel from overheating and preventing future operational issues. This overheating is prevented by raising the solar panels a few inches above the roof of the caravan to encourage airflow to cool the solar panels.

1 x Fischer ABS Glue for Supports and Grommets: accompanied by the grommet to insert the end of solar panels and their rubber from the extrinsic one. The ABS supports are made up of 4 corners and second time supports for the long pieces that will delimit the structure of the panel. This structure can specimen fixed by singular rubber for ABS. The ABS structures are convenient to prevent overheating of the solar panel and prevent future problems in its operation. This overheating is avoided by raising the solar panel of the caravan house a few centimeters, facilitating the flow of air that allows the solar panel to cool.

1 x Ultracell UC-138-12 12V 138Ah AGM Battery: From top brands like Ultracell, this AGM battery guarantees the best performance and longevity for your solar equipment. This is a deep cycle and represents the best in AGM lead-acid battery technology with electrolytes. Life expectancy exceeds 1100 cycles, but battery life can easily be doubled when discharged below 30%. AGM electrolyte is maintenance free and does not outgas, making it a very safe battery for indoor use. The battery has F1 screw terminals and weighs approximately 37 kg.

1 x SRNE MPPT 100V 30A 12/24V Regulator: is an advanced device to control solar charge with MPPT maximizer. A device that allows you to connect any type of solar panel to charge our 12V or 24V solar batteries with up to 30A. The SRNE MPPT 100V 30A 12/24V regulator stands out for its excellent technical characteristics with a very competitive price and 2-year manufacturer's warranty.

1 x SRNE BT-2 Bluetooth Adapter for MPPT MC: This Bluetooth adapter allows you to control the MC series range of MPPT controllers directly from your smartphone. This allows you to monitor and configure your regulator directly from your mobile phone. The included power cord draws power from the dimmer itself.

1 x 600W 12V Must Solar Inverter Charger: integrates a battery charger in one device, providing a very useful solution for small solar power systems. The nominal power is 600W and the maximum power for 20ms is 1800W. The nominal output voltage is 230 VAC. The battery supply voltage is 12 VDC. You can check the load, battery voltage, current, etc. on the LCD screen. This battery charger allows you to charge your battery from an external generator or power supply and features 10A at 12V. Compatible with sealed and open lead acid batteries. 0.5 meter cable of the required section is included. The inverter warranty is 2 years.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 5m red: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 5m black: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

2 x 6mm Cable Eye Terminal - 8mm Eye: used to crimp 6mm gauge cables and connect with 8mm diameter screws.

1 x WEIDMULLER PVStick Connectors – Most recommended if you don't have crimping tools that can connect normal MC4 connectors. They are compatible with all connector models that come standard with solar panels and require no tools to connect to the cable.

Solar kit to install in a camper van or motorhome with a 400W panel and up to 2,800W of production in summer.

The solar kit for camper van 500W 12V 2000Whdia is ideal for vans, caravans, motorhomes and boats since these usually have a service battery already installed

The solar kit comes with all the components to make it work so you don't need anything else.

The solar kit includes:

• 1 Solar Panel 400W Deep Blue 3.0 JA Solar Mono
• 1 ABS Solar panel support for caravans
• 1 Fischer ABS Glue for Brackets and Grommets
• 1 GEL 12V 300Ah Tensite Battery
• 1 Regulator MPPT 100V 30A LCD 12/24V
• 1 Victron Phoenix 12V 500VA Inverter
• 5 Unifilar Cable 6 mm2 SOLAR PV ZZ-F Red
• 5 Unifilar Cable 6 mm2 SOLAR PV ZZ-F Black
• Rest of wiring, terminals and connections

 By including a high-power 400W Monocrystalline Perc panel and an MPPT regulator with LCD screen, the solar kit has first-rate features.

Thanks to its large GEL battery and its Victron pure wave inverter, we will be able to cover the consumption of large caravans. It also includes the ABS structure to hold the plate to the ceiling.

Characteristics and powers of the offered system:

• Installed Photovoltaic Solar Power: 400 W
• Maximum output power to housing: 500VA
• Daily production in WINTER: 1.20 kWh
• Daily production in SUMMER: 2.80 kWh
• Annual AVERAGE daily production: 2.00 kWh

The characteristics of the components are:

- Solar Panel 400W Deep Blue 3.0 JA Solar Mono: it has a length of less than 180cm, it contains half cells that offer a very high efficiency that deliver 400W of power. It has PERC technology and is from the world-renowned manufacturer JA Solar.

- ABS solar panel support for caravans: Accompanied by the grommet to introduce the solar panel cable and its Sika brand glue from the outside.

- 12V 300Ah Tensite GEL Battery: Monobloc battery with GEL electrolyte technology and high capacity. Being GEL does not emit gases or require maintenance

- Regulator MPPT 100V 30A LCD 12/24V: Current controller up to 30A of SRNE that works at a voltage of 12V and 24V

- Victron Phoenix 12V 500VA inverter: This is a high-performance compact inverter, with a 2-year warranty. The strong points of the 500VA Victron pure wave inverter are its starting capacity and its stability in energy delivery.

The Caravan Solar Kit 800W 12V 1000Whdia with Gel Battery, feeds small consumption, such as lighting for hours or charging a cell phone.

Characteristics of the Caravan Solar Kit 800W 12V 1000Whdia with Gel Battery system

The photovoltaic system provided in the attached file can generate 0.60 kWh per day in winter (3 hours of sunshine) and 1.40 kWh in summer (7 hours of sunshine).

The characteristics of the proposed system are the following:

• Installed solar generation: 200 W
• Maximum output power to housing: 800VA
• Daily production in winter: 0.60 kWh
• Summer: daily production: 1.40 kWh
• Annual average daily production: 1.00 kWh

Caravan Solar Kit Components 800W 12V 1000Whdia with Gel Battery

1 x MUST 200W 12V Monocrystalline Solar Panel: suitable for caravans and 12V installations. It consists of 32 monocrystalline cells, weighs 10.3 kg and has dimensions of 1290 × 760 × 30 mm. The efficiency of the module is 20.4%, making it a very good option for small isolated houses with 3 or 4 panels and a 12V battery installed.

1 x ABS Solar panel support for caravans: includes cable glands to insert solar module cables and Sika brand adhesive from the outside. The ABS support consists of 4 corners and 2 supports in the long part that delimit the structure of the solar panel. This structure can be fixed with a special ABS glue. The ABS construction is helpful in preventing the solar panel from overheating and preventing future operational issues. This overheating is prevented by raising the solar panels a few inches above the roof of the caravan to encourage airflow to cool the solar panels.

1 x Fischer ABS Glue for Supports and Grommets: accompanied by the grommet to insert the end of solar panels and their rubber from the extrinsic one. The ABS supports are made up of 4 corners and second time supports for the long pieces that will delimit the structure of the panel. This structure can specimen fixed by singular rubber for ABS. The ABS structures are convenient to prevent overheating of the solar panel and prevent future problems in its operation. This overheating is avoided by raising the solar panel of the caravan house a few centimeters, facilitating the flow of air that allows the solar panel to cool.

1 x Ultracell UCG-172-12 12V 172Ah GEL Battery: From leading brands like Ultracell, this GEL battery guarantees maximum performance and longevity for your solar kit. This is a deep cycle and represents the best in lead-acid battery technology with a GEL electrolyte. Life expectancy is over 1200 cycles, but if discharged below 30%, battery life can be easily doubled and shortened. The GEL electrolyte is maintenance free and does not out gas, making it a very safe battery for indoor use. The battery has F11 screw terminals and weighs approximately 43 kg.

1 x 12V / 24V 20A PWM Must Solar Regulator: the 20A charge regulator works with a 12Vdc or 24Vdc battery and reports all the battery charging information (general operating status, battery voltage, current produced and temperature) from the panel includes an LCD screen to display In addition, this 10A solar charge controller from the manufacturer Must Solar can be easily configured to accurately charge batteries regardless of technology, ensuring perfect results and long battery life. It features a 12Vdc or 24Vdc output for DC-powered charging, 2 USB ports for charging mobile devices, and offers a 2-year manufacturer's warranty. The charge controller has protection against PV array short circuit, PV reverse connection, battery reverse connection, overload and output short circuit. Available from 10A to 60A in 12V DC and 24V DC models.

1 x Victron Phoenix 12V 800VA Inverter - This is a high performance compact inverter with a 2-year warranty. The strength of the Victron 800VA Pure Wave Inverter is its starting ability and stability of power output. It can handle the spikes that many electronic devices can have, such as small refrigerators and other devices that do not exceed about, 1200W. of maximum performance. Equipped with an LED light that constantly shows the status of the inverter. The Victron brand is a leader in the design and manufacture of sine wave inverters. A very reliable and at the same time compact inverter. Wiring is included to connect to the battery and the power outlet is a European Schuko plug.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m red: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m black: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

4 x 6mm Cable Eye Terminal - 8mm Eye: used to crimp 6mm gauge cables and connect with 8mm diameter screws.

1 x WEIDMULLER PVStick Connectors – Most recommended if you don't have crimping tools that can connect normal MC4 connectors. They are compatible with all connector models that come standard with solar panels and require no tools to connect to the cable.

The MPPT 8000Whdia Solar Expansion Kit is an extension that is used for solar installations.

• The MPPT 8000Whdia Solar Expansion Kit is an extension that is used for 24 and 48V solar installations in which we want to have a greater energy capture capacity. The regulator includes an LCD screen to be able to view and configure the parameters of our installation. If we use it in a 48V installation, the 60A of the MPPT would allow us to connect twice as many panels. It must be taken into account that this kit does not include a battery, a structure to hold the solar panels, or a 230Vac inverter, it is an extension that also includes wiring and accessories to make the corresponding connections.

Characteristics:

• Installed Photovoltaic Solar Power: 1,620 W
• Daily production in WINTER: 4.86 kWh
• Daily production in SUMMER: 11.34 kWh
• Annual AVERAGE daily production: 8.10 kWh

Kit Components:

• 4 x 405W Deep Blue 3.0 JA Solar Mono Solar Panel: The 405W Deep Blue 3.0 JA Solar Mono Solar Panel has some very particular characteristics. It contains half cells that offer a very high efficiency with 405W of power. It has PERC technology and is from the world renowned manufacturer JA Solar.
• 1 x MPPT 150V 60A LCD 12/24/48V regulator: This SR-ML MPPT charge regulator is a current controller up to 60A that works at a voltage of 12V, 24V, 36V and 48V. This charge regulator has advanced technology for monitoring the maximum power point of solar panels to optimize its efficiency at all times. Specifically, this MPPT charge regulator is capable of increasing efficiency between 15 and 20% compared to other PWM regulators. This charge regulator has an LCD screen for device configuration and data monitoring. Overheating protection of the regulator prolongs the life of the batteries.
• 1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m red: Special for electrical installations. Halogen-free and flexible power cable to meet the most demanding industrial requirements.
• 1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m black: Special for electrical installations. Halogen-free and flexible power cable to meet the most demanding industrial requirements.
• 5 x Single Wire Cable 16 mm2 SOLAR PV ZZ-F Red: Special for electrical installations. It is a halogen-free power cable. It is a flexible power cable designed to meet the most demanding industrial requirements.
• 5 x Single Wire Cable 16 mm2 SOLAR PV ZZ-F Black: Special for electrical installations. It is a halogen-free power cable. It is a flexible power cable designed to meet the most demanding industrial requirements.
• 3 x WEIDMULLER PVStick Connectors: They are the most recommended in the case of not having a crimper to be able to connect the usual MC4 connectors. They are compatible with all connector models that are offered as standard in solar panels and do not require any type of tool to assemble them on the cable.
• 1 x Parallel Connectors 2 Flexible MC4 PV Panels: They are the perfect complement to make a parallel connection of up to 2 panels in our solar installation

The 12V 1000Whdia Flexible Panel Kit offers the advantage of semi-flexible panels with a bending capacity of approximately 20°.

Characteristics of the 12V 1000Whdia Flexible Panel Kit system

The photovoltaic system provided in the attached file can generate 0.60 kWh per day in winter (3 hours of sunshine) and 1.40 kWh in summer (7 hours of sunshine).

The characteristics of the proposed system are the following:

• Installed solar generation: 200 W
• Daily production in winter: 0.60 kWh
• Summer: daily production: 1.40 kWh
• Annual average daily production: 1.00 kW

Components of the 12V 1000Whdia Flexible Panel Kit

2 x Flexible Solar Panel 100W 12V: it features high efficiency and offers flexibility, such as a curvature of up to 20°. Manufactured with maximum efficiency cells that allow excellent production in all types of atmospheric conditions. Its great power makes it ideal for boats, caravans, campers and other applications that require a source of solar energy, adaptable to all types of surfaces and lightweight.

1 x monoblock battery with high-performance GEL electrolyte technology: gelation does not generate gas and does not require maintenance. This is a great option if you plan to install the battery in an area with no ventilation. It is recommended to install it in a natural position. Never connect in parallel. To maximize the life of this battery model, the charging voltage must be considered. The price-performance ratio is remarkable, and the manufacturer offers a two-year warranty.

1 x Victron Smart Solar MPPT 75V 15A Regulator: regulator with charge current up to 15A and voltage up to 75V. In addition, the Smart Solar 75V 155A charge controller features ultra-fast Maximum PowerPoint Tracking (MPPT). The Smart Solar 75V 10A charge controller features advanced maximum PowerPoint detection in partly cloudy conditions. For its part, the Autosolar.es Smart Solar 75V 10A charge regulator model stands out for its conversion efficiency, flexible charging algorithms, reprogrammable auxiliary relays and complete electronic protection. It comes with a 5-year warranty. All Smart models have built-in Bluetooth, allowing you to set up and monitor the controller from your phone, tablet or PC using the Victron app.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m red: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m black: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

2 x 6mm Cable Eye Terminal - 8mm Eye: used to crimp 6mm gauge cables and connect with 8mm diameter screws.

1 WEIDMULLER PVStick Connector: Most recommended if you don't have crimping tools that can connect normal MC4 connectors. They are compatible with all connector models that come standard with solar panels and require no tools to connect to the cable

1 x Parallel Connectors 2 PV Panels MC4 Flexible: ideal for connecting up to 2 modules in parallel in a photovoltaic system.

The 24V Solar Pumping Kit for continuous use incorporates a Shurflo pump that works with a 24V power supply.

Characteristics of the 24V Solar Pumping Kit system for continuous use

The photovoltaic system provided in the attached file can generate 0.84 kWh per day in winter (3 hours of sunshine) and 1.96 kWh in summer (7 hours of sunshine).

The characteristics of the proposed system are the following:

• Installed solar generation: 280 W
• Daily production in winter: 0.84 kWh
• Summer: daily production: 1.96 kWh
• Annual average daily production: 1.40 kWh

Components of the Solar Pumping Kit 24V continuous use

1 x ERA Polycrystalline 160W 24V Solar Panel: it is a model called “grid connection” where the voltage is neither 12V nor 24V. With a 25-year performance guarantee made from polycrystalline silicon, our solar systems offer superior performance and high operational reliability. Due to the supply of non-standard voltages, the recommended connection series must be respected and used with MPPT controllers or grid connection systems. With 60 cells, this solar panel is one of the most powerful you can buy today and can deliver an average of around 1400Wh per day to the solar system. Keep in mind that production is much higher in summer than in winter. winter. Includes 1 meter cable for each pole with MC4 connectors at each end. A junction box with IP67 protection is included on the back of the solar panel. This photovoltaic panel comes with a pre-assembled aluminum frame and is ready to be fixed to any structure.

2 x Level Probe for ATERSA PM5 Controller: ATERSA's PM5 Level Probe is available in 12V and 24V and is used to control water pumps that use directly through solar panels.

1 x ATERSA PM5 24V Water Pump Controller: Atersa's PM5 water pump controller allows you to install a 24V water pump without a battery. Ideal for direct pumping systems and pressure groups where the water needs to be pumped or moved horizontally.

1 x Shurflo 24V Pressure Pump 2088-573-534 13 l/min - This is a Shurflo 24V 13.6 liters per minute pressure pump, pumps water from depths less than 3.6 meters, pumps water from rivers and pumps to reservoirs and ponds without The perfect solution for pumping and outside. Stop the pump every 30 minutes. The system allows the installation to be without batteries, so the water is only used during the day. Shurflo pressure pumps are excellent for pumping and moving water. Thanks to the ATERSA controller and a 200W 24V solar panel, the system works without batteries. Explore the product or view the data sheet.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m red: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x Roll Unifilar Cable 6mm2 H1Z2Z2-K 10m black: special for electrical installations. Halogen-free flexible power cables for the most demanding industrial requirements.

1 x WEIDMULLER PVStick Connectors – Most recommended if you don't have crimping tools that can connect normal MC4 connectors. They are compatible with all connector models that come standard with solar panels and require no tools to connect to the cable.